The EPAX X1K E6 LCD / MSLA 3D-printer is an open resin printer with a 405 nm light source, compatible with 3rd party resin. Full list of resin settings can be find here. Some resins have been optimized. Most other resins could also work on this printer, however, not all pre-settings are available. Contact us if you need support or have any questions.
Resin 3D-printing parameters for the EPAX X1K E6.
| Resin | Layer thickness | Curing time (seconds) | Remark |
| Strong-X | 100 µm | ||
| 50 µm | 15 | 4 base layers of 35 seconds | |
| 35 µm | |||
| Tough-X | 100 µm | ||
| 50 µm | 16 | 4 base layers of 40 seconds | |
| 35 µm | |||
| Flexible-X | 100 µm | ||
| 50 µm | 19 | 4 base layers of 40 seconds | |
| 35 µm | |||
| Deep Blue | 100 µm | ||
| 50 µm | |||
| 35 µm | |||
| Stone Coal Black | 100 µm | ||
| 50 µm | |||
| 35 µm | |||
| Premium White | 100 µm | ||
| 50 µm | |||
| 35 µm | |||
| Premium Black | 100 µm | ||
| 50 µm | |||
| 35 µm | |||
| Premium Model | 100 µm | ||
| 50 µm | |||
| 35 µm | |||
| Premium Flex | 100 µm | ||
| 50 µm | |||
| 35 µm | |||
| Premium Tough | 100 µm | ||
| 50 µm | |||
| 35 µm | |||
| Clear Impact | 100 µm | ||
| 50 µm | |||
| 35 µm | |||
| Composite-X | 100 µm | ||
| 50 µm | |||
| Hazard Glow | 100 µm |
Image by Epax3D: Their line-up of Epax resin 3D-printers.
EPAX X1K 6″ 2K MONO resin 3D-printer features
-
- – Parallel Matrix UV light source – This is the most advanced light source and available in the Epax3D E6 and E10 series. Providing more print detail for dental and jewelry applications where finer details are beneficial as well as a more even distribution of the light across the entire build area.
- – Light source closer to LCD screen – requiring less time for the resin to cure in the Epax E6 and E10 and extending the life of your LCD screen.
- – A 3.5-inch Color TFT Touchscreen is present in the Epax3D E6 an E10 resin 3D-printers.
- – 2K MONO (6 inch) LCD masking screen. 1620*2560 (2k) HD masking LCD allows for great print detail and much faster printing speed. It typically only needs a few seconds for normal resin, compared to color screen which needs 8 to 10 seconds for regular resin to cure. Pixel size is 50 microns.
- – The mono screen uses SX04 interface to mainboard. It can last several thousands hours of normal use.
- – Improved Z-axis stability.
- – Pre-installed nFEP film to allow easier detachment during printing (you can still use standard FEP films with this printer if you prefer).
- – Sanded build platform surface made of soft aluminum for better adhesion and easier print removal.
- – Anti-Aliasing supported and enabled in installed firmware. Effectivity depending on resin and settings.
- – Wide selection of supported resin – you can use any 405nm wavelength 3D-printing resin.
- – 128mm (L) *81mm (W) *155mm (H) build volume.
- – Built on our successful X1 frame, with a slightly larger mid plate in order to fit 6″ screen.
Contact us if you have any questions or when you need help with settings for the Epax 3D series or other resin based 3D-printers.
Support
Do you need any help with 3D printing our SLA, DLP or LCD resins? We can help you! Just look for the question you have below. If you can’t find it, let us know by contacting us!
